Hello Frank On my part n°122232-0 it's writen 57-32-9, does it mean there are two types of part 122245-1 ? The seller only propose me a 57-32-9.5 joint, hope it will go on... For the bearing rollers they don't find a way to get them... they only sell complete rollers Bearings And don't know size of ...

Thanks for your answers, in my position, something must have been déteriorated, because i've never open my gearbox before, and it works well before ! To start with, i'm gona change all my bearings, still got a problem with these parts, i don't fine anyu modern equivalent : n° 9912 n° 9647 n° 122224-...

Hello,

While i'm running my NZ350, the second gear (only the second) doesn't stay engaged and disengaged if i don't hold the hand gear lever.

I've open the gearbox, all the pinions seems to work well and are not damaged

Let me know your advice for origines of this problem.

thanks
ed

I've take out the dynamo, to check the brushes, no problem with that, and the spule resistance is 3,1 ohm on one wire and 10,6 ohm on the other one, my question is normally rhe big that is in series withe the feldspule should not be 13 ohms ??? (10 + 3)

Thanks
Ed

Hi frank, I checked first the regulator whatching the link you told me. When i connect 1 and 20 the charging light does not switch off, so normally the regulator is not out, Then after dismounted the regulator cartridge (shalter and régler) i put a voltmeter between 1 and the ground on the spulenkas...

Hi franck. I've tried to connect no more than 1 sec the pole 3 and 1. When i'm doing it, it switch off the orange light on the ignition key on the gaz tank, this light switch on again as soon as i'm disconnecting pole 1 and 3. It still not charging, the batt alone is 6,23V and when the engine is run...

It's'a NZ 350, how do you check the polarity ?

Thanks again.
Ed

Hello,

I'm trying to find how the shalter and regler works. all is the new, and it doesn't work. Do you know how to optimize de charge by truning the screw on the shalter and the regler ? Which resistance normally have to be the shalter and the regler mesureed separatly ?

Thanks
Ed

Hi everybody,

I'm looking for a Feldspule for a NZ 350 type.

Please contact me on my email edouard.callerot@gmail.com

or on my gsm: 0033 650 492 183

Bye
Ed

The rear fender is a good one as the front is. I had the original color under the paint. but i ha to work a lot on the rea fender beacause it was completely destroyed. So it probably doesn't look like exactly a good one!!!

Is that a good Nz350 head lamp? It doesn't look like the one on the parts explianation on the site.

Thanks
Edouard

hi, I've already ask for the light, it's on the way, for the seat, i got two, one one the bike seems not to be an original (i meen i had several problems to adapt it!) And the other one, i'm not sur the structure is good. Would you show me some photos of a good one in detail, particularly the mounti...

Here you got some photos of my bike: http://img687.imageshack.us/img687/1022/img5643l.jpg http://img690.imageshack.us/img690/5800/img5644j.jpg http://img710.imageshack.us/img710/999/img5650t.jpg http://img132.imageshack.us/img132/3083/img5651x.jpg http://img340.imageshack.us/img340/1540/img5652w.jpg...

Oh, i' forgot something, what is strange is that on the front fender the support for the number plate is for the short one, not so long as i've seen on most photos of NZ 350. And just after the support of the this plate i got four holes 20mm x 78mm, seems to be original ones.... Can you help me??? t...

Hi everybody, I'm restauring a NZ 350. I think it's an NZ 350 1943. Manufacturing year may be 1943...:roll: Frame number: 598 956 (number remarquared as it was the number on the papers! but the orginal one was incomplete and partially erased :( engine number 267 777 -72 ( stamped 8 43) and the cylin...