I have a problem with my nz-1, which is a court of restoration, the bike runs but only at idle.
when I turn the throttle. the cable works fine but no acceleration??
The carburetor is brand new purchased from Tilleman.
Thank you for any help.
help for my nz-1
Moderator: Mods
help for my nz-1
hello all,
I have a problem with my nz-1, which is a court of restoration, the bike runs but only at idle.
when I turn the throttle. the cable works fine but no acceleration??
The carburetor is brand new purchased from Tilleman.
Thank you for any help.
I have a problem with my nz-1, which is a court of restoration, the bike runs but only at idle.
when I turn the throttle. the cable works fine but no acceleration??
The carburetor is brand new purchased from Tilleman.
Thank you for any help.
-
matthias.koch
- Tool Cleaner
- Posts: 23
- Joined: Thu Dec 15, 2011 8:18 pm
- Location: Wiesbaden
Re: help for my nz-1
Stupid question: Are you sure you mounted the two cables, one for the gas slider and one for the air slider correctly?sam wrote:hello all,
I have a problem with my nz-1, which is a court of restoration, the bike runs but only at idle.
when I turn the throttle. the cable works fine but no acceleration??
The carburetor is brand new purchased from Tilleman.
Thank you for any help.
Re: help for my nz-1
Hallo Matthias,
Vielen Dank für Ihre Antwort, aber leider sind die Kabel korrekt installiert sind. Der Benzinhahn funktioniert gut.
als Vergaser. Die Bewegung in den Vergaser richtig zu funktionieren.
aber nicht immer umgehen Accelerator
Vielen Dank für Ihre Antwort, aber leider sind die Kabel korrekt installiert sind. Der Benzinhahn funktioniert gut.
als Vergaser. Die Bewegung in den Vergaser richtig zu funktionieren.
aber nicht immer umgehen Accelerator
Re: help for my nz-1
Hello everyone,
my problem now seems to solve part.
My air filter model nz-1 appears to be partly the cause.
Please note however, when I accelerates the bike accelerates not really, but only fitfully.
Do you have a lot of power on your nz accelerating??
my problem now seems to solve part.
My air filter model nz-1 appears to be partly the cause.
Please note however, when I accelerates the bike accelerates not really, but only fitfully.
Do you have a lot of power on your nz accelerating??
Re: help for my nz-1
Hi,
Have you noticed that the carburator should have a much smaller main jet when having a air cleaner of Zyklon type?
// Frank
Have you noticed that the carburator should have a much smaller main jet when having a air cleaner of Zyklon type?
// Frank
Re: help for my nz-1
Hello,
did you replace the nozzle carburetor
or you do so only with
screws, without changing the carburetor aj2-24?
Do you have a lot on your acceleration
nz??
Thank you for the help
did you replace the nozzle carburetor
or you do so only with
screws, without changing the carburetor aj2-24?
Do you have a lot on your acceleration
nz??
Thank you for the help
Re: help for my nz-1
Hi Sam,
The AJ Bing is ok, but you have to check the size of the main jet.
-If you have a normal mesh airfiltrer it should be number 110
-If you have a Zyklon airfilter it shoúld be number 85
As a first thing check out you have the rigt size of the main jet, after that you can try to adjust the idle mixture screw and try different needle heights to see what works best on your bike.
// Frank
The AJ Bing is ok, but you have to check the size of the main jet.
-If you have a normal mesh airfiltrer it should be number 110
-If you have a Zyklon airfilter it shoúld be number 85
As a first thing check out you have the rigt size of the main jet, after that you can try to adjust the idle mixture screw and try different needle heights to see what works best on your bike.
// Frank